Download CCNA Cisco Certified Network Associate CCNA (v3-0).passcertification.200-125.2019-10-07.1e.738q.vcex

File Info

Exam	CCNA Cisco Certified Network Associate CCNA (v3.0)
Number	200-125
File Name	CCNA Cisco Certified Network Associate CCNA (v3-0).passcertification.200-125.2019-10-07.1e.738q.vcex
Size	29.82 Mb
Posted	October 07, 2019
Downloads	900

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Download
ProfExam Simulator

Purchase
Coupon: EXAM_HUB

Discount: 20%

Demo Questions

Question 1

What are three characteristics of the TCP protocol? (Choose three.)

A: It uses a single SYN-ACK message to establish a connection.
B: The connection is established before data is transmitted.
C: It ensures that all data is transmitted and received by the remote device.
D: It supports significantly higher transmission speeds than UDP.
E: It requires applications to determine when data packets must be retransmitted.
F: It uses separate SYN and ACK messages to establish a connection.

Correct Answer: BCF

Question 2

Refer to the exhibit.

All of the routers in the network are configured with the ip subnet-zero command.
Which network addresses should be used for Link A and Network A? (Choose two.)

A: Link A – 172.16.3.0/30
B: Link A – 172.16.3.112/30
C: Network A – 172.16.3.48/26
D: Network A – 172.16.3.128/25
E: Link A – 172.16.3.40/30
F: Network A – 172.16.3.192/26

Correct Answer: AD

Question 3

Which type of device can be replaced by the use of subinterfaces for VLAN routing?

A: Layer 2 bridge
B: Layer 2 switch
C: Layer 3 switch
D: router

Correct Answer: C

Question 4

Which three statements about IPv6 prefixes are true? (Choose three.)

A: FEC0::/10 is used for IPv6 broadcast.
B: FC00::/7 is used in private networks.
C: FE80::/8 is used for link-local unicast.
D: FE80::/10 is used for link-local unicast.
E: 2001::1/127 is used for loopback addresses.
F: FF00::/8 is used for IPv6 multicast.

Correct Answer: BDF

Question 5

Refer to the exhibit.

The network administrator cannot connect to Switch 1 over a Telnet session, although the hosts attached to Switch1 can ping the interface Fa0/0 of the router. Given the information in the graphic and assuming that the router and Switch2 are configured properly, which of the following commands should be issued on Switch1 to correct this problem?

A: Switch1(config)# ip default-gateway 192.168.24.1
B: Switch1(config)# interface fa0/1
Switch1(config-if)# switchport mode trunk
C: Switch1(config)# line con0
Switch1(config-line)# password cisco
Switch1(config-line)# login
D: Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.24.3 255.255.255.0
E: Switch1(config)# interface fa0/1
Switch1(config-if)# duplex full
Switch1(confiq-if)# speed 100

Correct Answer: A

Question 6

Which two statements about IPv6 and routing protocols are true? (Choose two.)

A: EIGRPv3 was developed to support IPv6 routing.
B: OSPFv3 was developed to support IPv6 routing.
C: Loopback addresses are used to form routing adjacencies.
D: EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.
E: Link-local addresses are used to form routing adjacencies.

Correct Answer: BE

Question 7

What will happen if a private IP address is assigned to a public interface connected to an ISP?

A: A conflict of IP addresses happens, because other public routers can use the same range.
B: Addresses in a private range will not be routed on the Internet backbone.
C: Only the ISP router will have the capability to access the public network.
D: The NAT process will be used to translate this address to a valid IP address.

Correct Answer: B

Question 8

Which two statements about wireless LAN controllers are true? (Choose two.)