Download Implementing Cisco IP Switched Networks (SWITCH v2-0).actualtests.300-115.2018-08-08.1e.302q.vcex

Download Exam

File Info

Exam Implementing Cisco IP Switched Networks (SWITCH v2.0)
Number 300-115
File Name Implementing Cisco IP Switched Networks (SWITCH v2-0).actualtests.300-115.2018-08-08.1e.302q.vcex
Size 7.91 Mb
Posted August 08, 2018
Downloads 142

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Download
ProfExam Simulator

Purchase
Coupon: EXAM_HUB

Discount: 20%

ProfExam Simulator ProfExam Simulator ProfExam Simulator ProfExam Simulator ProfExam Simulator
 
 


Demo Questions

Question 1
Which of the following commands can be issued without interfering with the operation of loop guard?

  • A: Switch(config-if)#spanning-tree guard root
  • B: Switch(config-if)#spanning-tree portfast
  • C: Switch(config-if)#switchport mode trunk
  • D: Switch(config-if)#switchport mode access
Correct Answer: C



Question 2
The following command was issued on a router that is being configured as the active HSRP router. 
standby ip 10.2.1.1 
Which statement is true about this command?

  • A: This command will not work because the HSRP group information is missing
  • B: The HSRP MAC address will be 0000 0c07 ac00
  • C: The HSRP MAC address will be 0000 0c07 ac01.
  • D: The HSRP MAC address will be 0000.070c ad01.
  • E: This command will not work because the active parameter is missing
Correct Answer: B



Question 3
Routers R1 and R2 are configured for HSRP as shown below:
Router R1:
interface ethernet 0 
ip address 20.6.2.1 255.255.255.0 
standby 35 ip 20.6.2.21 
standby 35 priority 100 
interface ethernet 1 
ip address 20.6.1.1.2 255.255.255.0 
standby 34 ip 20.6.1.21 
Router R2:
interface ethernet 0 
ip address 20.6.2.2 255.255.255.0 
standby 35 ip 20.6.2.21 
interface ethernet 1 
ip address 20.6.1.1.1 255.255.255.0 
standby 34 ip 20.6.1.21 
standby 34 priority 100 
You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this?

  • A: physical layer issues
  • B: no spanning tree loops
  • C: use of non-default HSRP timers
  • D: failure to set the command standby 35 preempt
Correct Answer: A



Question 4
Which two statements about the HSRP priority are true? (Choose two.)

  • A: To assign the HSRP router priority in a standby group, the standby group-number priority priority-value global configuration command must be used.
  • B: The default priority of a router is zero (0).
  • C: The no standby priority command assigns a priority of 100 to the router.
  • D: Assuming that preempting has also been configured, the router with the lowest priority in an HSRP group would become the active router.
  • E: When two routers in an HSRP standby group are configured with identical priorities, the router with the highest configured IP address will become the active router.
Correct Answer: CE



Question 5
Which three statements are true of a default HSRP configuration? (Choose three.)

  • A: The Standby hello time is 2 seconds.
  • B: Two HSRP groups are configured.
  • C: The Standby track interface priority decrement is 10.
  • D: The Standby hold time is 10 seconds
  • E: The Standby priority is 100.
  • F: The Standby delay is 3 seconds.
Correct Answer: CDE



Question 6
Refer to the exhibit. What is the result of setting GLBP weighting at 105 with lower threshold 90 and upper threshold 100 on this router? 

 
  

  • A: Only if both tracked objects are up will this router will be available as an AVF for group 1.
  • B: Only if the state of both tracked objects goes down will this router release its status as an AVF for group 1.
  • C: If both tracked objects go down and then one comes up, but the other remains down, this router will be available as an AVF for group 1.
  • D: This configuration is incorrect and will not have any effect on GLBP operation.
  • E: If the state of one tracked object goes down, then this router will release its status as an AVF for group 1.
Correct Answer: B



Question 7
Which describes the default load balancing scheme used by the Gateway Load Balancing Protocol (GLBP)?

  • A: Per host using a strict priority scheme
  • B: Per session using a round-robin scheme
  • C: Per session using a strict priority scheme
  • D: Per GLBP group using a strict priority scheme
  • E: Per host basis using a round robin-scheme
  • F: Per GLBP group using a round-robin scheme
Correct Answer: E



Question 8
Which two statements about default FHRP behavior are true? (Choose two.)

  • A: A backup GLBP active virtual gateway can become active only if the current active virtual gateway fails.
  • B: Preemption is enabled by default.
  • C: Unless specifically Configured, the priority of an HSRP router is 200.
  • D: A standby HSRP router becomes active if it has a higher priority than the priority of the current active router.
  • E: A VRRP backup virtual router becomes the master router if its priority is higher than the priority of the current master router.
Correct Answer: AE



Question 9
To provide security, a service provider configures various private VLANs in its backbone network infrastructure to prevent certain VLANs from communicating to each other. 
Which version of VTP supports the use of private VLANs?

  • A: Version 1
  • B: Version 3
  • C: VTP does not support private VLANs
  • D: Version 2
Correct Answer: B



Question 10
Which statement about HSRP, GLBP, and VRRP is true?

  • A: VRRP group members communicate using multicast address 224.0.0.102.
  • B: MAC address 0000.0c07.acOc indicates that default gateway redundancy is provided through GLBP.
  • C: HSRP group members communicate using multicast address 224.0.0.18.
  • D: GLBP uses UDP port 3222 (source and destination) for hello messages.
  • E: MAC address 0c07.A698.8904 indicates that default gateway redundancy is provided through HSRP.
Correct Answer: D






CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset