Download CCIE Routing and Switching Written.braindumps.400-101.2018-11-12.1e.357q.vcex

File Info

Exam	CCIE Routing and Switching Written Exam v5.1
Number	400-101
File Name	CCIE Routing and Switching Written.braindumps.400-101.2018-11-12.1e.357q.vcex
Size	10.34 Mb
Posted	November 12, 2018
Downloads	69

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Download
ProfExam Simulator

Purchase
Coupon: EXAM_HUB

Discount: 20%

Demo Questions

Question 1

Refer to the exhibit. When R2 attempted to copy a file from the TFTP server, it received this error message. Which action can you take to correct the problem?

A: Change the access-list configuration onR1 to access-list 1 permit 172.16.1.0 0.0.0.255.
B: Configure the ip tftp source-interface Fa0/1 command on R1.
C: Configure the ip tftp source-interface Fa0/1 command on R2.
D: Configure the ip tftp source-interface LoopBack0 command on R1.
E: Configure the ip tftp source-interface LoopBack0 command on R2.

Correct Answer: E

Question 2

Which three modes are valid PfR monitoring modes of operation? (Choose three.)

A: route monitor mode (based on BGP route changes)
B: RMON mode (based on RMONv1 and RMONv2 data)
C: passive mode (based on NetFlow data)
D: active mode (based on Cisco IP SLAprobes)
E: fast mode (based on Cisco IP SLA probes)
F: passive mode (based on Cisco IP SLA probes)

Correct Answer: CDE

Question 3

R1 #sh ip sla configuration
IP SLAs Infrastructure Engine-III
Entry number: 1
Owner:
Tag:
Operation timeout (milliseconds): 1000
Type of operation to perform: icmp-echo
Target address/Source address: 10.1.2.2/0.0.0.0
Request size (ARR data portion): 28
Verify data: No
Vrf name:
Schedule:
Operation frequency (seconds): 2 (not considered if randomly scheduled)
Next Scheduled Start Time: Pending trigger
Group Scheduled: FALSE
Randomly Scheduled: FALSE
Life (seconds): 3600
Entry Ageout (seconds): never
Recurring (Starting Everyday): False
Status of Entry (SSMP RowStatus): notInService
Threshold (milliseconds): 2000
Distribution statistics:
Number of statistic hours kept: 2
Number of statistic distribution buckets kept: 1
Statistic distribution interval (milliseconds): 20
Enhanced history:
History statistics:
Number of history Lives kept: 0
Number of history Buckets kept: 15
History Filter Type: None
R1 # sh ip sla statistics
IPSLAs Latest Operation Statistics
IPSLA operation id: 1
Number of successes: Unknown
Number of failures: Unknown
Operation time to live: 0

Refer to the exhibit. For which reason could the statistics for IP SLA operation 1 be unknown?

A: The IP SLA schedule is missing.
B: The ICMP echoes were lost in transit.
C: The Type of Service parameter is configured incorrectly.
D: The Operation Frequency value is the same as the Operation Timeout value.
E: Data verification has been disabled.

Correct Answer: A

Question 4

An IP SLA fails to generate statistics. How can you fix the problem?

A: Add the debug ip sla error command to the router configuration.
B: Add the debug ip sla trace command to the router configuration.
C: Reload the router configuration.
D: Remove the ip sla schedule statement from the router configuration and re-enter it.
E: Add the verify-data command to the router configuration.

Correct Answer: E

Question 5

Refer to the exhibit.

Which two statements about this capture are true? (Choose two.)

A: It is set to run for five minutes.
B: It continues to capture data after the buffer is full.
C: It is set to run for a period of00:03:26.
D: It captures data only until the buffer is full.
E: It is set to use the default buffer type.

Correct Answer: AB

References:

Question 6

Which statement about NAT64 is true?

A: It uses one-to-one mapping between IPv6 addresses and IPv4 addresses.
B: It requires static address mapping between IPv6 addresses and IPv4 addresses.
C: It can be used to translate an IPv6 network to another IPv6 network.
D: It can be configured for stateless and stateful translation.

Correct Answer: D

Question 7

Refer to the exhibit.

Which two possible network conditions can you infer from this configuration? (Choose two.)

A: The authentication parameters on R1 and R2 are mismatched.
B: R1 is using the default NTP source configuration.
C: R1 and R2 have established an NTP session.
D: R2 is configured as the NTP master with a stratum of 7.

Correct Answer: AB

Answer A: The NTP associations are not synced, it is only listed as a candidate because it was configured. Routing is not the issue, so it must be mismatched authentication parameters. Answer B: NTP sets the source IP address for all NTP packets based on the address of the interface through which the NTP packets are sent. You can configure NTP to use a specific source IP address.

Question 8

Which option is the common primary use case for tools such as Puppet, Chef, Ansible, and Salt?