Download Implementing Cisco Enterprise Advanced Routing and Services.CertsHero.300-410.2023-01-12.1e.278q.vcex

Download Exam

File Info

Exam Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)
Number 300-410
File Name Implementing Cisco Enterprise Advanced Routing and Services.CertsHero.300-410.2023-01-12.1e.278q.vcex
Size 37.86 Mb
Posted January 12, 2023
Downloads 15

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAM_HUB

Discount: 20%

 
 



Demo Questions

Question 1
Refer to the exhibit.

        

Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. 
Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?

  • A: Issue the eigrp stub command on R1
  • B: Issue the no neighbor stub command on R2.
  • C: Issue the eigrp command on R2.
  • D: Issue the no eigrp stub command on R1.



Question 2
R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:

        

What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?

  • A: R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.
  • B: R1 does not accept any routes other than 192.168.130.0/24
  • C: R1 does not forward traffic that is destined for 192.168.30.0/24
  • D: Network 192.168.130.0/24 is not allowed in the R1 table



Question 3
Refer to the exhibit.

        

The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?
A)

        

B)

       
 
C)

        

D)

        

  • A: Option A
  • B: Option B
  • C: Option C
  • D: Option D



Question 4
Refer to the exhibit.

        

An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?

  • A: Dynamic routing protocols always have priority over static routes.
  • B: The metric of the OSPF route is lower than the metric of the static route.
  • C: The configured AD for the static route is higher than the AD of OSPF.
  • D: The syntax of the static route is not valid, so the route is not considered.



Question 5
Refer to the exhibit.

        

An engineer is trying to block the route to 192.168.2.2 from the routing table by using the configuration that is shown. The route is still present in the routing table as an OSPF route. Which action blocks the route?

  • A: Use an extended access list instead of a standard access list.
  • B: Change sequence 10 in the route-map command from permit to deny.
  • C: Use a prefix list instead of an access list in the route map.
  • D: Add this statement to the route map: route-map RM-OSPF-DL deny 20.



Question 6
Drag and drop the OSPF adjacency states from the left onto the correct descriptions on the right.




Question 7
Refer to the exhibit.

        

R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. 
What is the reason the route is not advertised?

  • A: R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
  • B: Route reflector setup requires full IBGP mesh between the routers.
  • C: In route reflector setup, only classful prefixes are advertised to other clients.
  • D: In route reflector setups, prefixes are not advertised from one client to another. 



Question 8
Refer to the exhibit.

        

In which circumstance does the BGP neighbor remain in the idle condition?

  • A: if prefixes are not received from the BGP peer
  • B: if prefixes reach the maximum limit
  • C: if a prefix list is applied on the inbound direction
  • D: if prefixes exceed the maximum limit



Question 9
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?

  • A: shared risk link group-disjoint
  • B: linecard-disjoint
  • C: lowest-repair-path-metric
  • D: interface-disjoint



Question 10
Refer to the exhibit.

        

What is the result of applying this configuration?

  • A: The router can form BGP neighborships with any other device.
  • B: The router cannot form BGP neighborships with any other device.
  • C: The router cannot form BGP neighborships with any device that is matched by the access listnamed "BGP".
  • D: The router can form BGP neighborships with any device that is matched by the access list named"BGP".






CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset