Download Certified Storage Installation Engineer, ONTAP.VCEplus.NS0-182.2019-11-22.1e.57q.vcex

Download Exam

File Info

Exam NetApp Certified Storage Installation Engineer, ONTAP
Number NS0-182
File Name Certified Storage Installation Engineer, ONTAP.VCEplus.NS0-182.2019-11-22.1e.57q.vcex
Size 1.06 Mb
Posted November 22, 2019
Downloads 4

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase
Coupon: EXAM_HUB

Discount: 20%

 
 



Demo Questions

Question 1
You have set up a new 2-node switchless cluster and want to verify that the failover is configured correctly.
In this scenario, which two commands accomplish this task? (Choose two.)

  • A: cluster ha show
  • B: storage failover show
  • C: cluster ring show
  • D: storage failover show-takeover



Question 2
You are completing an ONTAP base installation, and your customer is asking you to create two SVMs, one for NFS and one for SMB. Which type of SVM needs to be created to complete the installation?

  • A: system SVM
  • B: data SVM
  • C: admin SVM
  • D: multitenancy node SVM



Question 3
Which NetApp tool relies on PowerShell to produce a comprehensive handover report to the customer?

  • A: Active IQ
  • B: Config Advisor
  • C: NetAppDocs
  • D: Fusion



Question 4
Which LIF type is used by default for hardware-assisted storage failover communication?

  • A: intercluster
  • B: node-mgmt
  • C: data
  • D: cluster-mgmt 



Question 5

You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site. Referring to the exhibit, which steps are required to get an HA cabled system?

  • A: 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4.
    2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4.
    3. Cable the out-of-band ACP.
  • B: 1. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3.
    2. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.
  • C: 1. Insert a cable from right controller port 0a to IOMB port 1, and from port 0b to IOMA port 4.
    2. Insert a cable from left controller port 0a to IOMA port 1, and from port 0b to IOMB port 4.
    3. Cable the out-of-band ACP.
  • D: 1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3.
    2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.



Question 6

You just installed two nodes into an existing ONTAP cluster. When running date on the CLI you notice that the cluster1-03 node is running behind time. You confirmed that you can reach the node management LIF of each node. Referring to the exhibit, which statement is true?

  • A: The node-management LIF has to be on e0M for NTP to work.
  • B: The DNS is not configured for this node.
  • C: The NTP is adjusting in small increments.
  • D: No NTP server is configured for this node.



Question 7
When planning the installation of a new ONTAP 9.5 cluster for a customer, which three steps should you perform? (Choose three.)

  • A: Complete a Service Event Report.
  • B: Use Config Builder to create a configuration spreadsheet.
  • C: Review the hardware components in Hardware Universe.
  • D: Open a support case to prepare for the installation.
  • E: Search for Technical Support bulletins for the hardware.



Question 8
Node 3 has taken over Node 4. You are attempting to access Node 4 on its management interface but cannot do it. In this scenario, how would you access Node 4's management interface?

  • A: You must use the Service Processor; node management LIFS do not fall over between nodes.
  • B: You have not waited long enough for the failover timeout for a node management LIF; there is a broadcast domain configured for this situation.
  • C: You should use SSH directly to one of the cluster interconnect switches; from there, you can use SSH to the node management on node 4.
  • D: Connect to the node management on Node 3 and then use the HA interconnect to access node 4.



Question 9
You completed the installation of an AFF A700s with NetApp CN1610 switches. You used ports e0a and e0f with breakout cables to connect the controllers to the interconnect switches. After completing the cluster setup, ports e0e and e0i are not visible in OnCommand System Manager. In this scenario, what caused this problem?

  • A: Breakout cables were used and the second port on the same ASIC became disabled.
  • B: This is a hardware error and you must open a case with NetApp Support.
  • C: You must first enable the ports using the network port modify command.
  • D: You are missing a license to enable those ports.



Question 10
A 4-node cluster has connectivity for both block and file access. Nodes 1 and 3 are used for file access, and nodes 2 and 4 are used for block access. During routine maintenance, node 4 is switched off and the LIFs are migrated to other nodes. Upon investigation, you see that the LIFs that serve file traffic have moved to alternative ports. However, LIFs that serve the block have not migrated. In this scenario, what is happening?

  • A: The failover group is configured incorrectly.
  • B: The fiber switch is configured incorrectly.
  • C: There is a faulty SFP.
  • D: The LIFs that serve the block protocol do not failover.









CONNECT US


ProfExam
PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount..

Get Now!


HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen



HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset