Download Troubleshooting Cisco Data Center Infrastructure (DCIT).300-615.VCEplus.2024-08-09.93q.vcex

ProfExam Suite - Black Friday
Vendor: Cisco
Exam Code: 300-615
Exam Name: Troubleshooting Cisco Data Center Infrastructure (DCIT)
Date: Aug 09, 2024
File Size: 9 MB
Downloads: 1
Download Exam

How to open VCEX files?

Files with VCEX extension can be opened by ProfExam Simulator.

Download
ProfExam Simulator

Purchase
Coupon: EXAM_HUB

Discount: 20%

ProfExam Simulator ProfExam Simulator ProfExam Simulator ProfExam Simulator ProfExam Simulator

Demo Questions

Question 1
You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?
  1. The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.
  2. Rebooting the APICs and the leaf and spine switches after wiping them is not required.
  3. You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.
  4. The same Fabric Name value should be used before after wiping all devices.
Correct answer: C
Question 2
An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a "resolve slot" warning. Which server maintenance action resolves the issue?
  1. Perform diagnostic interrupt on the server.
  2. Re-acknowlegement the server.
  3. Reset the server.
  4. Decomission the server.
Correct answer: B
Question 3
Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?
  1. Modify the VLAN assignment to vNICs.
  2. Change the PIN groups on the vHBAs.
  3. Modify the FCoE VLAN.
  4. Set the FCoE VLAN as the native VLAN on server uplinks.
Correct answer: C
Question 4
Refer to the exhibit.
  
An engineer is performing a health check on ACI. Which statement about interface Ethernet 1/11 is true?
  1. The interface is working correctly and fully operational, but it is not in use.
  2. The interface policy is misconfigured.
  3. "out-of-service" is the default interface status in ACI.
  4. "out-of-service" indicates that no service graph is in use for this interface.
Correct answer: B
Question 5
A user reports that they cannot reach from a UCS server to an FC Storage array. Which command is used to test communication between an FCF and a target?
  1. fcroute
  2. traceroute
  3. fcping
  4. ping
Correct answer: C
Question 6
An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)
  1. M-Series module
  2. ESSENTIALS license
  3. STORAGE-ENT license
  4. FCoE license
  5. F-Series module
Correct answer: DE
Question 7
Refer to the exhibit.
  
An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?
  1. Configure the role name to match the group name on Microsoft Active Directory.
  2. Include specific users into MDS role configuration.
  3. Configure SSH logins on Cisco MDS switch.
  4. Integrate Cisco MDS with Microsoft Active Directory.
Correct answer: A
Question 8
Refer to the exhibit.
  
An attempt to bind the Ethernet interface to vFC fails. Which action resolves the issue?
  1. Add the FCoE VLAN to the allowed VLAN list.
  2. Configure the FCoE VLAN that corresponds to the vFC VSAN as a private VLAN.
  3. Configure the interface as a trunk port.
  4. Configure the interface to use the native VLAN of the trunk port.
Correct answer: C
Question 9
Refer to the exhibit.
  
A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch.
The switch fc2/10 NP uplink is shown in the exhibit. Which action ensures that fc2/10 is in an up state?
  1. Replace the SFP port module in fc2/10.
  2. Configure the admin port type E on the upstream switch that connects the port.
  3. Enable NPIV on the upstream switch that connects the port.
  4. Configure the BB_credit buffers on the upstream switch that connects the port.
Correct answer: C
Question 10
Refer to the exhibit.
  
The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?
  1. VSAN 1 is suspended.
  2. The SFP is unsupported.
  3. Trunk mode must be activated.
  4. The interface is in an incorrect mode.
Correct answer: A
CONNECT US
HOW TO OPEN VCE FILES

Use VCE Exam Simulator to open VCE files
Avanaset

HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files
ProfExam Screen

ProfExam
ProfExam at a 20% markdown

You have the opportunity to purchase ProfExam at a 20% reduced price

Get Now!